Navigation
23 users online :: 23 Guests and 0 Registered
Most popular FAQs
- Should step pegs and safety climb be included in ... (677343 views)
- Section 2.6.9.2What does the term “In the absence of ... (655862 views)
- I am a structural engineer in Oregon, and I ... (655811 views)
- Section 2.6.9.2Is it acceptable to use the results of ... (651243 views)
- Section 2.6.9.2Is it acceptable to use the results of ... (642763 views)
- Section 2.6.9.2Can I use loading that is less than ... (640536 views)
- Section 2.6.9My question is regarding how to determine the ... (616473 views)
- Section 4.9.9: I’m using this section to calculate the ... (589380 views)
- Section 4.9.9: I'm using this section to calculate the ... (587888 views)
- 1) I knew this table 4-8 is used to ... (576241 views)
Latest FAQs
- I have a question regarding TIA-222-H Clause 2.6.9 & ... (2021-09-22 18:19)
- I have a question regarding TIA-222-H Clause 2.6.9 & ... (2021-09-22 18:17)
- I have a question regarding TIA-222-H Clause 2.6.9 & ... (2021-09-13 19:53)
- Can ASCE 7-16 wind maps be used per TIA-222-G ... (2020-01-16 16:14)
- Section 15.7 Exemption 7, states to use a 50% ... (2019-12-18 21:39)
Sticky FAQs
- How do I use this Site?
- Do we have to do a structural analysis on ...
- Does the Standard apply to the design of antennas? ...
- How to submit a question?
- Section 2.6.9.2What does the term “In the absence of ...
- Section 2.6.9.2Is it acceptable to use the results of ...
- Section 2.6.9.2Can I use loading that is less than ...
- Section 2.6.9.2Is it acceptable to use the results of ...
- Section 13.3 question regarding plumb measurement of monopoles; submitted ...
- Figure A1-1 Why were the tables and Note 3 ...
- 1) I knew this table 4-8 is used to ...
- 2.6.7.4 Gust Effect Factor for Structures Mounted on Other ...
- Is there reciprocity between ANSI/TIA-222-G and CSA S37-01? In ...
- Section 15.5 indicated "A feasibility report shall state ...
- Section 2.6.6 Calculating the topographic factors
- As everyone is aware, many jurisdictions are now adopting ...
- Section 2.7.3 states “Further, …earthquake effects may be ignored ...
- I am currently working a telecommunications tower project where ...
- Is there a tolerance recommendation for base plate to ...
- in case of telecommunication tower to be built on ...
- Is there a tolerance recommendation for base plate to ...
- in case of telecommunication tower to be built on ...
- The definition of Z in sections 2.6.5.2, 2.6.6.4, and ...
- If Ca=1.5 is used for a rectangular cluster of ...
- Section 2.6.5.2 “Velocity Pressure Coefficient”Question: Shall “z” in the ...
- Section 4.9.9: I'm using this section to calculate the ...
- Section 2.6.6.4 - Rev-G provides a simplified method of ...
- WHICH IS THE unbraced length "L" TO CONSIDER, ACCORDING ...
- Does section 2.8.2 Limit State Deformations of ANSI/TIA 222-G ...
- Where it has been suggested in previous posts that ...
- We understand section 2.6.4.1 to apply only to areas ...
- Waveguides, downleads, and other cables are frequently strapped to ...
- Should step pegs and safety climb be included in ...
- Section 3.6.2 note 1 regarding pattern loading and tower ...
- Approximately when will the next revision or amendment to ...
- I have a tower for which the plumb and ...
- In Section 4.4.1 of TIA/EIA-222-G December 2009 the minimum ...
- Section 3108.1 of the 2012 IBC eliminates the 222-G ...
- Section 9.6 What is the intent of the grade ...
- One thing I recently noticed was in Table C1, ...
- Regarding recent FAQ 1128: would it be possible to ...
- I’m trying to determine if a pad & pier ...
- Is it the intention of drafters of the TIA ...
- Section 2.6.5: Addendum 2 defines Exposure Category C as ...
- Section 5.4.2 gives requirements for Non Pre-Qualified Steel stating ...
- Which of the states adhere to the Rev G ...
- In Section 4.5.1, the following language is used:"A multiple ...
- Shall “z” in the equation be based on mid-height ...
- Section 4.9.9: I’m using this section to calculate the ...
- Section 2.6.6.4 - Rev-G provides a simplified method of ...
- Which is the unbraced length to consider, according to ...
- I am a commercial building reviewer for the City ...
- Does section 2.8.2 Limit State Deformations of ANSI/TIA 222-G ...
- Can section 2.8.2 also be applied to a TIA-222-F ...
- Table 4-6 provides slenderness requirements for horizontal members, specifically ...
- Where it has been suggested in previous posts that ...
- One thing I recently noticed was in Table C1, ...
- In Section 4.5.1, the following language is used:"A multiple ...
- Is it acceptable to use Ka = 0.6 for ...
- For double angles, are the modified (KL/r)m equations shall ...
- K is not mentioned on the right side of ...
- Is (KL/r)o shall include the curves defined in Table ...
- Section 4.9.8. Does the definition of Guy Assembly Link ...
- Section 12 Climbing Facilities in TIA-222-GWhat is the strength ...
- Section 12 Climbing Facilities TIA-222-GWhat is the strength requirement ...
- Section 4.5.3 Built-Up Members states that "A minimum of ...
- Referencing Section 2.3.2, Exception 4 and Note 3; for ...
- Is there any back up material for the usage ...
- I am a structural engineer in Oregon, and I ...
- Section 2.6.1: In the definitions section of 2.6.1, a ...
- Does TIA-222-G include any consideration of loads other than ...
- Should mounts be subjected to Section 15 requirements that ...
- Hello,The effective projected area of transmission lines mounted in ...
- Section 2.6.9My question is regarding how to determine the ...
- Hello. A question was asked about the validity of ...
- The inspection intervals are recommended. Can I extend the ...
- Is there any available document or article that explains ...
- Section A.2.2 and Table 2-1 establish the classification of ...
- Section A.2.2 and Table 2-1 establish the classification of ...
- The industry is on the verge of the release ...
- Do T-Arm mounts classify as Sector Mount or a ...
- When an EPA at an elevation is specified in ...
- Use of Survival wind speed with ANSI/TIA-222H : There ...
- Section 15.7 Exemption 7, states to use a 50% ...
- Do T-Arm mounts classify as Sector Mount or a ...
- Section 15.7 Exemption 7, states to use a 50% ...
- Can ASCE 7-16 wind maps be used per TIA-222-G ...
- I have a question regarding TIA-222-H Clause 2.6.9 & ...
TIA TR14 STEERING COMMITTEE FAQ News
TIA TR14 FAQ
This is a not for profit web site provided to disseminate information regarding the above Standards published by the TIA TR-14 Committee. Responses to FAQs are prepared by the TR-14 Steering Committee with the intent to provide insight and clarity into the background and decisions made in the formulation of the Standards referenced above. Each FAQ response represents the consensus opinion of the TR-14 Steering Committee. The FAQ responses shall not be substituted for each user’s responsibility to understand and implement the Standards in accordance with Engineering theory, ethics and laws. The TIA TR-14 Committee for the noted Standards disclaims for itself, its committee members and the Telecommunications Industry Association any liability for any injury to persons or to property or other damages of any nature whatsoever, whether special, indirect, consequential or compensatory, directly or indirectly resulting from the use of or reliance upon information contained on this web site or application of the activities or devices referenced herein. This FAQ does not modify or update any standards and is not a substitute for the implementer’s own research, judgement, and engineering experience. This FAQ is for information purposes only and helps the Committee understand where updates to the standards may need to be made in future revisions.
Last update: 2019-10-16 14:55
Author: TIA TR14 STEERING COMMITTEE
You cannot comment on this entry